THE BASICS OF PLUMBING SKILLS FOR BATHTUB INSTALLATION

The Basics of Plumbing Skills for Bathtub Installation

The Basics of Plumbing Skills for Bathtub Installation

Blog Article

Website

Just how do you feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub
Installing a bathtub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard task. If the old tub is conveniently obtainable, the job can move quickly; if you need to open a wall to remove the old tub as well as place the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will require a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified on your own for the job as well as fit trying it. Rather than employing a contractor to take control of a halfway-completed project, it is better to take into consideration using one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly help you mount a new bathtub in your bathroom if you have actually already gotten a new bathtub and do not need to change the setup of your previous supply of water pipelines.
Your tools as well as product checklist ought to comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited accessibility that is typically the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
    Before going on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipelines.
    If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in place in between the faucet and the sink. Secure the faucet in position with the maker provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Setting up the Bath tub


    Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
    The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and adjusting the feet on the bath tub till the spirit level reviews degree.
    To set up taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
    Turn on the water system as well as check all joints as well as new pipework for leakages as well as tighten them if required. Fill the bathtub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub should wait up until the bathtub has been made use of a minimum of when as this will settle it right into its last placement.

    Getting ready for the Installment


    Firstly, the supporting structure supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to stop strain on the tub.
    Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.

    Tiling Around the Bath tub


    In the area where the bath satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not think about this motion before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the tiles using waterproof or waterproof sticky and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I was shown that report on Tools You Need to Install a New Bathtub through a good friend on another site. Feel free to take the time to distribute this write-up if you appreciated it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Connect for plumbing excellence now.

    Report this page